[Chimera-users] question

A G Szabo agszabo at bell.net
Fri Dec 2 10:33:15 PST 2016


Elaine

I am including the structure I am working with in Chimera. Don't know if you
can see it  in the message. So I attached a copy


You can see that I have shown a selection of residues. If I were to use the
command "~disp #0.1" then the other residues would disappear. I tried to use
the command you suggested "disp #0.1:33.K,37.K,38.K" since the Gly residues
are on Chain K #0.1. and I wanted to retain the atoms of the displayed side
chains on Chain C #0.1 and Chain E #0.1. I  had turned ribbackbone off since
I thought according to your suggestion I could display all the atoms of the
three Gly residues  on Chain K #0.1.

Unfortunately it didn't work. But thanks for your suggestions.



arthur

-----Original Message-----
From: Elaine Meng [mailto:meng at cgl.ucsf.edu] 
Sent: December-02-16 12:47 PM
To: A G Szabo
Cc: chimera-users at cgl.ucsf.edu
Subject: Re: [Chimera-users] question

Hi Arthur,
Unfortunately "ribbackbone" only applies to the whole model.  However, it is
merely an "enabler" allowing backbone atoms and ribbon to be shown at the
same time, if the atoms and ribbon both happen to be displayed for the same
residue.  You can still hide (~display) any atoms you don't want to see and
hide ribbon (~ribbon) of any residue whose ribbon segment you don't want to
see.

So you would have to use "ribbackbone #0.1" or something like that on the
whole model, but then hide all the atoms you don't want, say "~disp #0.1" to
hide all atoms, and then to show all atoms of glycines 33,37,38 it could be
something like "disp #0.1:33.A,37.A,38.A" (for example, if they are in chain
A of model #0.1).

Again, you can use Selection Inspector instead of commands for many things,
although commands are better for doing things with specific residue numbers.
I hope this helps,
Elaine
-----
Elaine C. Meng, Ph.D.                       
UCSF Computer Graphics Lab (Chimera team) and Babbitt Lab Department of
Pharmaceutical Chemistry University of California, San Francisco


On Dec 2, 2016, at 9:33 AM, A G Szabo <agszabo at bell.net> wrote:

> You have been very helpful in explaining different  items that use the
command line.
> 
> I have a PDB file that was determined by NMR. Thus there are a large
number of chains number as pdb (#0.1) Chain A   etc.
> 
> So I know that I can select a single chain, and build up an image with
Chains A, B, etc using the #0.1 chain number.
> 
> I want to visualize three Gly residues in one chain. So I learned that I
can use the command ribbackbone  to visualize the backbone atoms of the
amino acids that I  want to show. So when I use that command all the
backbone atoms of the residues selected are visualized including the side
chains. I also know that if I use the command ~ribbackbone  all the backbone
atoms are suppressed leaving only the atoms of the side chains. I  know that
without any residues or atoms specified the command applies to the whole
model.
> 
> Now as I said that I  want to visualize three Gly residues in one of the
chains. The Gly residue numbers are 33, 37, 38.  They are on Chain #0.1 K.
> 
> The information on the ribbackbone  in the  Chimera users guide, 
> indicates that I should be able  to do this by using parameters termed 
> atom-spec.  i.e. ribbackbone  atom-spec
> 
> 
> I looked elsewhere for how to designate the parameters for atom-spec and
tried a few things, but I was not able to achieve the specificity of showing
the backbone atoms of only the Gly residues. I don't think that I have to
indicate that I want only the Gly residues in Chain K #0.1 because I can
select the Gly residues from the sequence of Chain K #0.1.
> 
> So after this long description of what I want to do, would you kindly
inform me of how I can visualize the backbone atoms of only Gly.
> 
> Thank  you
> 
> Arthur G. Szabo

-------------- next part --------------
A non-text attachment was scrubbed...
Name: figure for Elaine.pptx
Type: application/vnd.openxmlformats-officedocument.presentationml.presentation
Size: 127658 bytes
Desc: not available
URL: <http://plato.cgl.ucsf.edu/pipermail/chimera-users/attachments/20161202/d18aef76/attachment-0001.pptx>


More information about the Chimera-users mailing list